JDSU TP300 User's Guide Page 1

Resi-Testerf Whole-House Cable TesterUser's Guidewww.jdsu.com/know

7Network (NTWK) Cable Test Mode - The Resi-Tester™ assumes the 8-position jack on the main unit and the remote will be used for connecting the tester

8“Split” icon and the word “OFF” appearing on the screen briefly indicates this. Another long press will toggle back to the split pair testing, and s

9pattern duration. Pressing any button other than TONE turns off the Resi-Tester™. The tone will turn off automatically after about 2.4 hours.Volts

10Instructions for UseResi-Tester™ powers off automatically 9 minutes after the last button press in cable testing modes and after 2.4 hours in tone

11To Test CoaxAttach one end of cable to be tested to F-connector on main unit. Remove remote unit from main unit by squeezing the remote lightly betw

12To Place Tone on a CableConnect cable to be traced to a main unit jack. For best signal, do not connect a remote to the other end. Due to the shie

13Interpreting Cable Test ResultsThe Pass icon will be on if the cable has all pins properly connected per T568A/B for network cables or per 3-pair U

14Short - The pair has a low resistance connection from one wire of the pair to the other wire of the pair or to any other wire in the cable or the s

157&8 are the pairs designated by T568A/B for a RJ45 jack or plug. A cable can be wired with correct continuity but not with correct pairing. Th

161111111122222222333333334444444455555666667777788888SHORTT568A/B Passing Cable (unshielded)(1 not twisted with 2; 3 not twisted with 6)3 4 5 6 7 8OP

17Battery ReplacementWhen the battery low icon is on, the battery should be replaced as soon as practical. The cable testing results will become unre

18SpecicationsPhysical Dimensions:Size: 13.2 x 7.3 x 4.1 cm (5.2 x 2.9 x 1.6 inches)Weight: 242 grams (8.5 oz.) with battery and remoteEnv

19AccessoriesLB32 - 24”, F push-on plug to alligator clip set (to use with TP315)TP20 - 7.5” cable assembly with no-fault 6 position plugs, reverse-

20TP315 - Set of 20 Speaker Seeker™ alliga-tor clip remote identiers for Resi-Tester™ and Testier™TP608 - Set of 7 numbered remotes for LanScaper™,

21Customer Services This section provides a description of customer services available through JDSU (including returns policies and procedures) and wa

22manufactured equipment. This ensures products meet all published specifications, including any applicable product updates. Calibration — JDSU’s cali

23problem or service requested. The name and telephone number of the person to contact regarding questions about the repair. The return authorization

24Warranty Information JDSU guarantees that its products will be free of all defects in material and workmanship. This warranty extends for the period

25is reused, recycled, or disposed of in an environmentally friendly manner, and in compliance with all applicable national and international waste le

26Notes:

Resi-TesterTONECOAXNTWKTELTEL - (Telephone cable test)Press to power on and begin testing. Tests to 3-pair USOC on standard and 6-position RJ-jack. Pr

27Notes:

Document InformationDoc. # TU9856Revision 500, 05-08Englishwww.jdsu.com/know

1WARNING!Do not attach to AC power. The Resi-Tester™ may be damaged and cause a safety hazard for the user.CAUTION!Improperly crimped, damaged or un-

2FeaturesTests network (8-wire), telephone (6-wire) and coax cabling systemsSupports 8 network remotes and 20 coax remotes (optional, see accessory li

3DescriptionThe Resi-Tester™ is designed to test all common low voltage cabling systems found in today’s automated businesses and homes; telephone, n

4Upon completion of a telephone or network cable test, the wire map, ID and any faults are displayed. The top line of numbers on the display represen

5In the coax mode, the “Open”, “Short” or “Pass” icon will be on to indicate the results of a test. If the cable passes, the “ID” icon will be on as

6standard to define the pairs. Connector pins 1-6, 2-5 and 3-4 are the pairs defined by this standard. The tester will display the “Pass” icon when