User's Guidewww.jdsu.com/knowTestifierf All Cable Tester
6standard to define the pairs. Connector pins 1-6, 2-5 and 3-4 are the pairs defined by this standard. The tester will display the “Pass” icon when
7Network (NTWK) Cable Test ModeThe Testifier™ assumes the 8-position jack on the main unit and the remote will be used for connecting the tester to th
8the word “OFF” appearing on the screen briefly indicates this. Another long press will toggle back to the split pair testing, and so on. When split
9options are dual or warble tones of differing pattern duration. Pressing any button other than TONE turns off the Testifier™. The tone will turn o
10Instructions for UseTestifier™ powers off automatically 9 minutes after the last button press in cable testing modes and after 2.4 hours in tone mo
11To Test Coax/Un-terminated two (2)conductor wire (speaker)Attach one end of cable to be tested to F-connector on main unit. Remove remote unit from
12To Place Tone on a CableConnect cable to be traced to a main unit jack. For best signal, do not connect a remote to the other end. Due to the shie
13Interpreting Cable Test ResultsThe Pass icon will be on if the cable has all pins properly connected per T568A/B for network cables or per 3-pair U
14connection from one wire of the pair to the other wire of the pair or to any other wire in the cable or the shield. A short is indicated by the Sho
15with correct continuity but not with correct pairing. This most often happens when the cable is terminated consistently at both ends, but in the wr
161111111122222222333333334444444455555666667777788888SHORTT568A/B Passing Cable (unshielded)(1 not twisted with 2; 3 not twisted with 6)3 4 5 6 7 8OP
17Battery ReplacementWhen the battery low icon is on, the battery should be replaced as soon as practical. The cable testing results will become unre
18SpecicationsPhysical Dimensions:Size: 13.2 x 7.3 x 4.1 cm (5.2 x 2.9 x 1.6 inches)Weight: 242 grams (8.5 oz.) with battery and remoteEnv
19Models, options & accessoriesOrder numberDescriptionTP300Resi-Tester cable tester with built-in remote (identical functionality with Testifier)T
20TP312Set of 20 (1-20) RJ45 remote identifiers TP311Set of 20 (1-20) coax remote identifiers TP310Set of 10 (1-10) coax remote identifiers TP309#1 ne
21KP321Testifier cable tester TP350 and set of 20 (1-20) RJ45 wiremappers TP312 in a pouch TU8809KP315Total Test-Wiremapping Kit: Resi-Tester cable te
22Customer Services This section provides a description of customer services available through JDSU (including returns policies and procedures) and wa
23manufactured equipment. This ensures products meet all published specifications, including any applicable product updates. Calibration — JDSU’s cali
24problem or service requested. The name and telephone number of the person to contact regarding questions about the repair. The return authorization
25Warranty Information JDSU guarantees that its products will be free of all defects in material and workmanship. This warranty extends for the period
TestifierTONECOAXNTWKTELTEL - (Telephone cable test)Press to power on and begin testing. Tests to 3-pair USOC on standard and 6-position RJ-jack. Pres
26is reused, recycled, or disposed of in an environmentally friendly manner, and in compliance with all applicable national and international waste le
Document InformationDoc. # TU9856-1Revision 500, 06-08Englishwww.jdsu.com/know
RJ12RJ45(Shielded)RJ12COAXF-Conn.RJ45(Shielded)Front ViewRemote UnitTop ViewMain Unit
1WARNING!Do not attach to AC power. The Testier™ may be damaged and cause a safety hazard for the user.CAUTION!Improperly crimped, damaged or un-cri
2FeaturesTests network (8-wire), telephone (6-wire) and coax cabling systemsSupports 8 network remotes and 20 coax remotes (optional, see accessory li
3DescriptionThe Testifier™ is designed to test all common low voltage cabling systems found in todays automated businesses and homes; telephone, netw
4Upon completion of a telephone or network cable test, the wire map, ID and any faults are displayed. The top line of numbers on the display represen
5In the coax mode, the “Open”, “Short” or “Pass” icon will be on to indicate the results of a test. If the cable passes, the “ID” icon will be on as
Comments to this Manuals